|Inoken MVP V3|
|Innoken MVP 3|
The iTaste MVP3.0 has a flush 510 connection with a spring loaded positive pin, durable stainless steel threading, an included ego adaptor and a replaceable integrated micro-USB charging cable.
The iTaste MVP3.0 e cigarette has a variable voltage range of 3.0 – 9.0 volts adjustable in 0.1 volt increments and a variable wattage range of 6.0 – 30.0 Watts, adjustable in 0.5 watts increments.
The iTaste MVP3.0 uses vRMS DC current and is very accurate with a power deviation of 0.1 Watt. The full 30Watts is precisely maintained between resistances of 0.4 to 2.5 ohms. There is no wasted power and exact accuracy means you are always vaping the power level that you choose. vRMS provides superior precision in delivering the exact wattage Ohm’s Law requires and stable power means better vapor.
The Primary Features of The iTaste MVP3.0
Battery Level Indicator:
The iTaste MVP3.0 e cgiarette battery has a tri-color LED on the top.
Green = Almost fully Charged. When the iTaste MVP3.0 is fully recharged the top LED light will power off.
|30 Watt MVP3|
Yellow = Half Power.
Red = Low Power. Charge the MVP3.0.
Variable Voltage:Voltage can be adjusted from 3.0 – 9.0 volts in .1 volt increments.
Variable Wattage:Wattage can be adjusted from 6.0 – 30.0 Watts in .5 watts increments.
Low Voltage Warning:The Red LED and Battery bar will continue blinking when the battery capacity is lower than 3.3V and the iTaste MVP3.0 Advanced Personal Vaporizer will automatically power off.
Short Circuit/Atomizer Protection:Short Circuit/Atomizer Protection protects the iTaste MVP3.0 Advanced Personal Vaporizer against shorted atomizers and will stop the unit from functioning in unsafe conditions.
The iTaste MVP3.0 features automatic real-time atomizer Ohms detection. If the resistance of the atomizer is lower than 0.4 the Ohms bar will blink and the MVP3 will not power on.
‘Vape while charging’ Technology
The iTaste MVP3.0 is recharged with a Micro USB cable. When plugged into a power source the iTaste MVP3.0 can also be vaped and charged at the same time with Innokin Technology’s ‘Vape while you charge’ pass-through technology.
Remembers last Voltage or Wattage setting:When the iTaste MVP3.0 is turned off it will remember the current voltage or wattage setting and it will retain the setting when the iTaste MVP3.0 is powered on.
Portable power source for electronic products:To charge your portable electronic device with the iTaste MVP3.0 plug the built-in Micro USB cable into the electronic device and power on the MVP3.0. The included iTaste MVP3.0 starter kit charging cable can also be used. Plug the larger USB port into the MVP3.0 and the Micro-USB into the electronic device and power on the iTaste MVP3.0. You may only charge one electronic device at a time. Do not attempt to charge more than one device at the same time or you may damage the device.
High compatibility 510 connector:
The iTaste MVP3.0 510 threading is compatible all standard 510 clearomizers & atomizers including the iClear16, iClear16B, iClear16D, iClear30, iClear30B, iClear30S and the Gladius-M.
Operating Voltage: 3.0V-9 V
Operating Wattage: 6.0W-.30W
Standby current: 100uA max
Maximum output Wattage: 30W
Maximum output Current：10A
Maximum output Voltage: 9V
Clearomizer Resistance: 0.4 Ohm (minimum)
Battery: Built-in 3800 mAh polymer Li-Ion rechargeable battery.
Charging: Micro USB DC5V/1A
OUTPUT port ：DC5V /1A
Whats in the Box:
1x iTaste MVP3.0 battery
1x USB charger cable
1x eGo Threading Adaptor
1x English manual
1x Acrylic box